만도브로제 모바일

제품

품질 및 가격 경쟁력을 바탕으로 장기적인 협력 관계 유지

우리 회사는 지속적인 성장을 위해 협력업체로부터 우수한 품질과 가격경쟁력을 갖춘 부품 구매에 최선을 다하고 있습니다.

또한 협력업체와 동반 성장을 위한 안정적인 협력 관계를 구축하고 있습니다.

보상 구매 일반 현황

Mechatronics 부품: 우리회사는 우수한 성능과 신뢰성을 갖춘 부품을 구매합니다. 또한 “불량 제로”를 지향합니다. 품질이야말로 고객의 신뢰를 얻을 수 있는 최선의 길이기 때문입니다.
Cable Harness 및 각종 전기전자 부품들은 우리의 모터를 완성하기 위한 매우 중요한 부품입니다.

Electronics: Integrated electronics with position sensor systems

Wire Harness: - Sensor harnesses,
length from 200 mm to 1000 mm, with specified connectors
Connection cable for Electronic Power Steering Motors, partially with over-molded lead frame; - Power harnesses

Electronical Components: Active Components (Microcontroller, Driver ICs, Transceiver) and Passive
Components in SMD and THT technology Relays and PCB

Connectors and PINS: Housing and connectors for electronics in 1K or 2K, partly with over-molded lead
frame Pin and stamping parts with press fit-technology

Covered Copper Wire: Nominal Diameter 0.03 mm - 2.2 mm
Temperature Index 180 - 220°C

Hybrid Components: Contact units, Function/Carrier housings with a variety of
technologies such as Silicon injection molding,
bonding-, welding and soldering techniques

Metal 부품: 우리 회사가 생산하는 모터는 우수한 정밀도, 고기능성 및 내구성이 장점입니다. 이를 위해 최고 품질의 스틸 및 알루미늄 등 다양한 소재들이 사용되고 있습니다.

Steel: - Coils
   CR, HR,
   Material thickness from 0.6 mm to 5.0 mm
   Bearing shield, Distance ring, Decoupling ring
   Conical washer, Curved washer; - Steel wire rod/Round bar
Material diameter from Φ10.0 mm to Φ15.3 mm
Shaft

Stamped and formed parts: Part made off hot or cold rolled material,
thickness from 0.8 mm to 3.0 mm

Welded parts: Laser welding after stamping

Die casting parts: Aluminum Alloy, motor housings with precision-machining,
ready for assembly, Net weight up to 500 gram

Wire-formed-parts: With material diameter from 0.5 mm to 8.0 mm,
small stampings with material thickness from 0.25 mm to 1.5 mm,
partially with assembling scopes

Turned parts: Made of steel, machined, partly hardening and grinding Diameter from 4.0 mm to 20 mm

Laminations: Single laminations or lamination stacks out of electrical steel,
material thickness from 0.5 to 1.0 mm, with or without powder coating

Bearings: Ball bearings from 22 mm to 32 mm outer diameter

Cold forging parts: Fasteners made of steel, cold forged according to drawing, ready-to-install,
galvanized or coated, Part weight from 1 gram to 260 gram

Powder metal parts: Part weight from 5 gram to 80 gram also with gear teeth

Magnets: - Sintered NdFeB Magnets
Block type rare earth magnets

Surface treatment: - Shaft
High frequency induction heating; - Electric Terminal
plating

Plastic 부품: 각종 플라스틱 부품들은 점차 자동차 기술에서 중요한 역할을 늘려가고 있습니다. 우리 회사의 모터에도 이러한 초경량, 고강성 소재의 플라스틱 부품을 사용하고 있습니다. 가벼운 소재의 플라스틱 부품은 연료 소비를 줄이고, 결국 CO2 배출 감소에 기여합니다.

Pellets: Mainly of basic material : PA46, PBT, PPA

Plastic injection molded parts: Plastic parts with one or multi component injection molding,
large plastic parts manufactured by injection molding, stamping, lightweight
materials, ready to assemble/use

Rubber formed parts: Made of HNBR, EPDM

FAMILY SITE

family site더보기